Question # 1

Laser beam technology is used for.

Choose an answer

terminals

optical disk

keyboards

magnetic tape

The analog computer deal directly with.

Choose an answer

number or pulses

measured values of continuous physical magnitudes

signals in the form of 0 or 1

signal in discrete values form 0 to 9

Computer output produced as small film images is called

Choose an answer

OCR

COM

LCD

OMR

How many types of data transmission modes are there?

Choose an answer

2

3

4

5

Scheduling deadlines and milestones can be shown on a.

Choose an answer

system survey

decision table

prototype

Gantt chart

Computer is a combination of:

Choose an answer

Software

Hardware

Both A and B

None

A device which connects multiple nodes to the network is

Choose an answer

A modem

A Hub

A repeater

A router

A LAN is a combination of.

Choose an answer

LAN cables

Network adapter card

LAN Application Software

All of the above

A microprocessor has memory location from 0000 to 3FFF, each storing one byte. The number of bytes, the memory can stored is.

Choose an answer

8,192

16,384

32,768

4,096

The major operational problem of the early first generation computers was

Choose an answer

inaccurate results

poor reliability

delayed results

limited capabilities

Computer follows a simple rule called GIGO, GIGO stand for

Choose an answer

good input, good output

great instructions, great output

garbage in, garbage out

gated input, gated output

Computer operations are synchronized by.

Choose an answer

the CPU clock

megabytes

the binary system

E-time

A graph prepared by a computer.

Choose an answer

Is its output

Is the piece of information to user

Is a hard copy

All of the above

The output of a sequential circuit depends upon

Choose an answer

present input

past inputs

both a and b

none of a and b

Soft copy refers to

Choose an answer

OCR-A

screen output

microfiche

digitizing

On a linear bus topology cabling can be extended by using following device

Choose an answer

Network Adapter Card

Barrel Connector

Terminator

Modem Card

PDP-5,PDP-8,IBM-360 series and IBM-370 series belong to the.

Choose an answer

first generation computers

second generation computers

third generation computers

fourth generation computers

The equipment attached to CPU which computer can access are called.

Choose an answer

hardware

input/output devices

peripherals

computer components

The type of modulation that changes the height of the signal is called.

Choose an answer

frequency

phase

amplitude

prephase

_________is input device.

Choose an answer

Keyboard

Touchpad

Microphone

All

Cabling on a linear bus topology can be extended using which of the following?

Choose an answer

Terminator

Barrel connector

Network adapter card

Medium attachment unit

Data gathering and data analysis take place.

Choose an answer

after the system survey

after system analysis

during system design

during evaluation

The ENIAC, using ABC principles, was designed by.

Choose an answer

Charles Babbage

Bell Laboratories

John V. Atanasoff

Mauchly and Eckert

Which of the following is increasing as computer technology progresses?

Choose an answer

speed

efficiency

hardware reliability

all of these are inceasing

ASCII 7 bit code can represent maximum

Choose an answer

265 character

128 character

64 character

65536 character

At the beginning of the instruction cycle, the contents of the Instruction Register specify.

Choose an answer

Operand for the instruction being executed

Instruction itself

Operand for the instruction to be executed next

None of above

Logical multiplication refers to operation of.

Choose an answer

OR gate

AND gate

NOT gate

inverter gater

Retaining data for future reference is called

Choose an answer

storing

sorting

memorizing

programming

Which of the following is not hardware

Choose an answer

Magnetic tap

Printer

VDU terminal

Assembler

During E-time the ALU.

Choose an answer

examines the instruction

enters the instruction

executes the instruction

elicits the instruction

Electronic Numerical Integrator and Calculator (ENIAC machine) belongs to the

Choose an answer

first generation digital computer

second generation computer

third generation computer

fourth generation computer

More Classes

Other Links

ECAT Computer Science Online Test MCQs With Answers

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer

Choose an answer